Just How to Remove and Change a Tub.
Just How to Remove and Change a Tub.
Blog Article
We've discovered this great article about A Step-by-Step Guide to Installing a Bathtub down the page on the net and felt it made perfect sense to talk about it with you on my blog.
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old tub is readily available, the job can move rapidly; if you need to open up a wall surface to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your washroom if you have already acquired a new tub and also don't need to transform the arrangement of your previous water supply pipelines.
Your devices and also material list ought to comprise the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath must be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the bath tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last placement.
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic due to the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 little points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the level checks out level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other faucet.
Turn on the supply of water and also inspect all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and the regular outlet for leakages.
Finally, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Secure the faucet in position with the manufacturer offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were introduced to that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on our other web address. Are you aware of another individual who is involved in A Step-by-Step Guide to Installing a Bathtub? Why not promote it. Thank you for taking the time to read it.
Schedule Estimate Report this page